Posts Tagged ‘Warrick Controls’

DFL and 26B Warrick Controls Series Overview

January 22nd, 2012

The Warrick Controls Series DFL and 26B controls

They are reliable float less probe form central heating boiler level controls, which contains distributed electrode probe fitted using a sensing unit that extends into the water boiler.

 DFL and 26B Warrick Controls Series OverviewAn insulated probe wire attached to the control is connected to the sensor rod which is designed to function by holding down the current flow in the water through the probe(s) and analyzing the current flow through a fixed set point resistor.  This is dependable due to no-moving-parts exposed to water.

 The Warrick Controls Line DFL and “26 B” right side control are noted to operate like a low h2o cutoff on vapor and warm water heater solutions.

The left side is used as a pump control on steam boilers when high water alarm is required and electric water needs valve control.

 Warrick Controls Series ADVANTAGES AND FEATURES:

1. RELIABILITY.  As a floatless type, control needs limited service with sole stainless sensor rod revealed to the water and no-moving-parts in the liquid.  An independent transformer within the handle is unattached to the low voltage 12 Volts path through the supply line.

2. LONG LASTING WITH LOW MAINTENANCE COST. The system is an ascended remote panel in the boiler control to avoid conduction of heat which accumulates more life of the electrical elements.

3. SIMPLICITY. Other than common blow down on steam boilers, Warrick controls’ boilers have no necessary complication in parts that needs regular attention.  The level is controlled to certain limits by expanding the probe with no necessary adjustments needed.  The control does not require necessary stuffing boxes, bellows or mercury switches, floats which can lead to serious shutdown and expensive repairs.

4. UNDERWRITERS’ LABORATORIES. It notes 26B and on the right side as Limit Controls while on the left side as Motor Controller of DFL control system.

5. QUALITY CONSTRUCTION.  The system has compact circuitry with Light emitting diode indicators for level safety and pump on.  The Warrick controls low water cutoffs promotes waiting times for continued safety and programmed recycling on interrupted power even if it is provided with manual recast.  Pump controls promotes waiting times for starter and avoid short cycling of pumps.

RECOMMENDED APPLICATIONS:

1. It applies like a reduced h2o cutoff and water pump control on regular central heating boilers with probes set-up in the water column.

2. It applies as a secondary low water cutoff on all regular steam boilers aside from (U drum) type.  The probe ascends in usable situation on higher installation in the h2o line linking to the vapor drum using the sensing unit expanding within the drum in just One inch on the surface.

3.  It applies like a reduced h2o cutoff on all regular Direct Fired Hot Water Boilers with the probe attached in the boiler header or system water level in vertical position.

4.  It applies like a very low water cutoff on all length and sizes of regular Roundabout Water Heating units. The probe ascends within the higher header in vertical position.

5.  It is highly suggested as Warrick controls high water alarm solely when needed by Code with the probe attached in a vertical position.

share save 171 16 DFL and 26B Warrick Controls Series Overview

Warrick Controls Starter Kits

January 10th, 2012

There are times when you might need to refill the current tank that you have or drain it. Maybe the vessels need pressurized or the wells need to be done. These are just a couple of reasons as to why warrick controls  kits could come in handy and help you out with your problem.  Both the pro’s and the beginners will be able to learn about the components plus how to add in everything that they need because of the kits.

When you get one of the starter kits from Warrick Controls

You will literally find that it does have everything in it that you need. You will even be able to do operations such as pumping down and pumping up. All of the kits come with the right probes, controllers, enclosures that you will find to be electrical so be careful when handling them and of course, it provides the instructions on every kit regardless of what one you decide to get or need.

The TK Kits from Warrick Controlswc 150x150 Warrick Controls Starter Kits

happen to be suited for when you need to drain them open or either refill them. If you do not know what you are doing with warrick controls then this could be just as complicated and difficult to understand without the kit. The TK-1 kit was created in such a way to help you with being able to refill the pumps and control them automatically so you won’t have any problems with it. The open ponds and tanks will then be able to drain without any issues. The best part about the TK 1 kit is that you will find that there is not any kind of assembly needed. The wires just need to be connected properly.

The next kit available is the WK 2 Kit which can be used for when you are designing wells. The wells will be able to drain the way that they should and the pump down of the wells will also be able to fit the right way. However, assembly is actually required with this kit but there are instructions provided for when it comes time to assemble everything together.

The HP – 1 Kit is the other one that you might need to help with draining or refilling the pressure vessel. You will find that this kit controls the refill pumps so it automatically does everything the way that it should. Some warrick controls might require assembly that is minimal such as this one. The application that is opposite gets applied to the Hp 2 kits.

When you need kits for warrick controls then it is very important that you do the research required in order to make sure that you have the right kit. You will find some great prices online to help you save some money for when you get the kits. Regardless of what kit you get they should always have the instructions and everything that you need in order to get everything put together the right way. Without these warrick controls kits it could be very complicated to do but these kits should make it easier for you.

share save 171 16 Warrick Controls Starter Kits

Shopping for Warrick Controls

December 30th, 2011

When you are in need of finding high quality conductive liquid monitoring and parts that don’t move then you might want to look into warrick controls. You will find that the system is reliable and dependable. It is very safe to use and the cost is not as much as you think it might be. You will be amazed at the number of software products that is provided to help including starter kits. These starter kits happen to be perfect for the beginner and even pros might find that they are saving time when they use these kits. The starter kit comes with everything that you need in order to get you started.

Some of the warrick controls series includes:

Series  16 & 16D, Series 26, Series DF, Series 17 & 27, Series 47, Series 67, Series 16M and Series 16HM, Series 16DM and 16VM, Series 26M, Series 19MR and please note, that before buying that the Series one has been discounted and if you would like a quote for the Series AM then you should call for one. These just happen to be some of the series involved. Be sure that you research and find what kind of series might be the best one for you to get and call if you have any questions to ensure that you get the right one.

If you are new or might just be starting out with warrick controls

Then getting a beginner kit might be the best thing for you to do. Most of the starter kits tend to be very affordable and you will be amazed at how much you will learn with the warrick controls starter kits. Once you have your starter kit and which to advance you will be able to easily do so but many people get these kits when they are just starting off plus it even help with saving money since everything is in a kit you will not have to buy a bunch of things separately and that can save you a lot of time.

The series all vary with warrick controls and it’s important to make sure that you get the right one. If you are unsure as to what series you need then don’t hesitate to call or email us. You might even find your answers with just looking and researching online. There is a lot of information on the web in regards to these controls that can help you out with what you are doing.

Looking online for these kinds of controls is really the best thing for you to do. You will find that you will save a lot more money and will find the prices to be very reasonable. In stores you might also find that warrick controls could be very expensive but you won’t find that is the case when you look online. Once you figure out what series you need and what might help you out the most you will be very glad that you researched warrick controls, and got it online at a great price.

share save 171 16 Shopping for Warrick Controls
Privacy Policy http://privacypolicy.warrickcontrols.net/wp/